[résolu] primtux5 et ltsp

[manu]

Je me suis fait l'installation depuis le début bien au propre pour te donner des informations cohérentes.
Je suis sur une box avec l'adresse de base 192.168.1.1.
Les 2 cartes en automatique DHCP.

Code :

root@primtux:/home/administrateur# ip a
1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000
    link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00
    inet 127.0.0.1/8 scope host lo
       valid_lft forever preferred_lft forever
    inet6 ::1/128 scope host
       valid_lft forever preferred_lft forever
2: enp3s0: <NO-CARRIER,BROADCAST,MULTICAST,UP> mtu 1500 qdisc fq_codel state DOWN group default qlen 1000
    link/ether 00:e0:1c:3f:5a:47 brd ff:ff:ff:ff:ff:ff
3: enp0s25: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc fq_codel state UP group default qlen 1000
    link/ether 00:23:ae:58:39:f0 brd ff:ff:ff:ff:ff:ff
    inet 192.168.1.26/24 brd 192.168.1.255 scope global dynamic noprefixroute enp0s25
       valid_lft 85817sec preferred_lft 85817sec
    inet6 fe80::1903:b344:d669:43c5/64 scope link noprefixroute
       valid_lft forever preferred_lft forever
root@primtux:/home/administrateur#

1. installation de Primtux5
2. mise à jour
3. le ppa LTSP
4. l'installation comme sur le site LTSP
Jusque la tout va bien.
5.je mets la seconde carte en manuel 192.168.67.1 /24 et je ne touche pas a la premiere je lance

Code :

ltsp dnsmasq --proxy-dhcp=0

et la plus de connection web avec firefox????
pourtant si je ping la box, je la trouve!

et je me suis arrêté là. et j'attends tes lumières

je te donne les fichiers .conf pour terminer ( on dirait que NAT est en commentaire??)

Code :

# /bin/sh -n
# LTSP configuration file
# Documentation=man:ltsp.conf(5)

# The special [server] section is evaluated only by the ltsp server
[server]
# Enable NAT on dual NIC servers
# NAT=1
# Provide a full menu name for x86_32.img when `ltsp ipxe` runs
# IPXE_X86_32_IMG="Debian Buster"

# The special [common] section is evaluated by both the server and ltsp clients
[common]
# Specify an alternative TFTP_DIR
# TFTP_DIR=/var/lib/tftpboot

# In the special [clients] section, parameters for all clients can be defined.
# Most ltsp.conf parameters should be placed here.
[clients]
# Specify an /etc/fstab line for NFS home; note this is insecure
# FSTAB_HOME="server:/home /home nfs defaults,nolock 0 0"

# MAC address, IP address, or hostname sections can be used to apply settings
# to specific clients.
[61:6c:6b:69:73:67]
# HOSTNAME=pc01
# Include parameters from another section, defined below
# INCLUDE=crt_monitor

# Shell "case" expressions can be used in MAC, IP, or hostname sections.
# This matches all Raspberry Pi MAC addresses.
[b8:27:eb:*|dc:a6:32:*]
# FSTAB_BOOT="/dev/mmcblk0p1  /boot  vfat  defaults  0  2"

# If you have proper DNS, you can use hostname sections
[administrator-pc]
# Only allow the administrator to log in to this client
# PWMERGE_SUR="administrator"

# You can also group parameters into named sections and INCLUDE= them elsewhere
[crt_monitor]

Code :

# This file is part of LTSP, https://ltsp.org
# Copyright 2019 the LTSP team, see AUTHORS
# SPDX-License-Identifier: GPL-3.0-or-later

# Configure dnsmasq for LTSP
# Documentation=man:ltsp-dnsmasq(8)

# For additional local dnsmasq configuration like DNS blacklisting, it's
# recommended to use separate /etc/dnsmasq.d/local.conf files,
# so that they're not lost if you ever (re)run `ltsp dnsmasq`.

# port=0 disables the DNS service of dnsmasq
port=0

# enable-tftp enables the TFTP service of dnsmasq
enable-tftp

# FHS 2.3+ recommends /srv for tftp (debian #477109, LP #84615)
tftp-root=/srv/tftp

# Log lots of extra information about DHCP transactions
#log-dhcp

# IP ranges to hand out, usually on the internal LTSP subnet of 2-NIC setups
dhcp-range=192.168.67.20,192.168.67.250,12h

# If another DHCP server is present on the network, a proxy range may be used
# instead. This makes dnsmasq provide boot information but not IP leases.
#dhcp-range=set:proxy,192.168.0.0,proxy,255.255.255.0

# Specify the DNS server. 0.0.0.0 means the machine running dnsmasq.
# DNS_SERVER in ltsp.conf is preferred as it reaches proxy DHCP clients.
dhcp-option=option:dns-server,8.8.8.8,208.67.222.222

# Set some tags to be able to separate client settings later on.
# "39" means "recent iPXE with menu support": http://ipxe.org/howto/dhcpd
dhcp-match=set:iPXE,175,39
dhcp-match=set:X86PC,option:client-arch,0
dhcp-match=set:X86-64_EFI,option:client-arch,7
# Due to rfc4578 errata, sometimes BC_EFI=9 is misused instead of X86-64_EFI=7:
dhcp-match=set:X86-64_EFI,option:client-arch,9
dhcp-mac=set:rpi,b8:27:eb:*:*:*
dhcp-mac=set:rpi,dc:a6:32:*:*:*